Dialogic Brooktrout TR1034 BRI Instrukcja Użytkownika Pobierz pdf (Strona 22)

22 Chapter 3 Dialogic Analog Fax Boards

The following table lists all of the Dialogic analog fax boards supported by RightFax.

Warning The voltage level supplied by the CPD/220 fax board is considered dangerous. Never operate the

system when the chassis cover has been removed.

Setting the I/O address

Before installing your Dialogic fax boards, you may need to manually set the base I/O address of

each board.All fax boards are shipped from Dialogic with a default I/O address of 350. If more than

one fax board is installed in the same computer, this will result in an I/O address conflict. All of the

channels on each installed Dialogic board must have a unique I/O address.

Warning Do not use a pencil or any other object that conducts electricity to move DIP switches on any fax

board. Using graphite and other electrically conductive materials may cause severe damage to the board.

On the Dialogic CP, CP1, CPi/100, and CPD fax boards, the I/O address is set using six DIP

switches located on the mounting bracket. On the Dialogic CP4/LSI, CPi/200, and CPD/220 fax

boards, the I/O address is set using three DIP switches on the unit marked “SW1” on the fax board.

Refer to your Dialogic documentation for the location of the I/O address DIP switches on your

particular fax board.

Note The Dialogic CPi/200 PCI and CPi/400 PCI fax boards do not require you to set I/O address values.

Instead, these board models include a rotary switch that lets you specify a unique identifier number for each

installed board. For information on setting the unique identifier on these board models, see ”Setting the

board identifier” on page 24.

The I/O setting represents the first channel on the board. Any additional channels on the board

automatically use the next I/O addresses in sequence. If you are installing multiple boards, make

sure that the I/O address settings do not overlap. Any changes to the I/O address DIP switches

must be made before the fax board is installed.

Table 3A Supported Dialogic Analog Fax Boards

Board model Description

One loop-start channel ISA analog fax board. You can install up to 16 Dialogic CP boards

in a single computer.

CP4/LSI Four loop-start channel ISA analog fax board.

CPD

One DID channel ISA analog fax board. You can install up to 16 Dialogic CPD boards in a

single computer. Requires an external –48V DC power supply.

CPD/220

Two loop-start and two DID channel ISA analog fax board. If your computer has a 220

watt power supply, you can install a maximum of two CPD/220 boards in one computer. If

your computer has a 300 watt power supply, you can install a maximum of three

CPD/220 boards.

CPi

One loop-start channel ISA analog fax board. You can install up to 16 Dialogic CPi

boards in a single computer.

CPi/100

One loop-start channel ISA analog fax board. You can install up to 16 Dialogic CPi/100

boards in a single computer.

CPi/200 Two loop-start channel ISA analog fax board.

CPi/200 PCI Two loop-start channel PCI analog fax board.

CPi/400 PCI

Four loop-start channel PCI analog fax board. You can install up to six Dialogic CPi/400

boards in a single computer.

XPI One loop-start channel ISA analog fax board.

XPI/100 One loop-start channel ISA analog fax board.

XPI/200 Two loop-start channel ISA analog fax board.

1 2 ... 17 18 19 20 21 22 23 24 25 26 27 ... 35 36

Komentarze do niniejszej Instrukcji

Brak uwag

Dialogic Brooktrout TR1034 BRI Instrukcja Użytkownika Strona 22

Komentarze do niniejszej Instrukcji

Powiązane produkty i podręczniki dla Networking Dialogic Brooktrout TR1034 BRI